The Nordkap 476 {part 6}

      Now that 'ole Nordie was upright, I started with the bow.  the first thing to do was the anchor boxes.  I was a little concerned about it because there was some shrinkage involve here....in the deck platform and in the skeleton itself.  the ribs to the bow were off and I had to cut some of the second rib away away to fit the boxes in place.  I added a small piece of wood at the bottom to close them off and create a sill for the bottom.  I had to cut them from the inside out.  one side fared better than the other, but after they are fitted with their rub rails and painted, they will look fine.

    the starboard side, pictured here, has the hole cut out.  I have the first bow rib in place, the rest soon followed.  I also had to add  extra wood, so that i could space the second bow rib.

     for the outer wall, I fitted a needle nozzle in the tube of wood filler and sealed along the bulwarks.  the tubes of Elmer's wood filler that i have {oak and natural} have been around a while.  I had to knead the tubes like crazy, just to get some out.  the natural tube, I was able to make it sit at the bottom, creating the airgap at the nozzle.  I added some water.....not too much......sealed it up and kneaded the hell out of it.....I even shook it!  it comes out like a paste.....I was surprised that I could use the needle nozzle on it.  the little compartment is interesting....I have some ideas as to what I want to do with it.  I can't go much further here, can't put on the forecastle cover because now I'm in question as to how the anchors are affixed.  no matter....I can finish and paint the hull before this is done.....there are other places i can go......     
      I figured I'd also get started on the pilot house......bottom section.  the first big problem I see right now, is that the house itself has a slope.  the parts were warped a little, but I reinforced the assembly and for the moment, left it separated from the main wall at the stern.  I want it to be removable for the moment for what i want to do to it later.  but for now, lets get the helm platform to sit flush.  I am doing all I can to keep the "separation lines"  from being too prominent {I've seen other builds}.  I had to be a human vise {because I don't have any} for one part of it's assembly.......had to ask my wife to get a beer for me.....but she loves me!
      I also added a pillar in the center of the front wall to sure it up.   I also thought about the port holes.....just how much light will be in there.  I made a floor for the open area in the middle.  I've had suggestions on lighting, but I will hold off on that for now......I want to do a few kits first.   my next task is to do just that, fitting the helm platform.....can't wait to see how i get out of this one.  I'll be working on the stern parts when I begin, because it also depends on how they fit too.

     you can see the gap in the middle of the deck platform......shrinkage.  there is a little at the front of this structure, but it will be covered with planking.....no worries.  I'm going to have to put on the deck railings, but I will have to paint the bulwarks a light gray {the housing too, so they will match}. color is starting to come to the Nordkap

The Nordkap 476 {part 5}

     the hull is starting to take shape.  I'd add skim coats of filler to the rough areas of the hull, do something else for a while till it dried and then sand.  the worst part was the first sanding....a lot of it.  when I waited for the second application to dry, I started to think about how I was going to set him up good and proper....I wanted to start doing things on the deck { can't wait}.  I have to include a short piece on the cradle.....it just looks so darn cute!  LOL!   the direction were very plain {I just looked at the picture}...my only regret is that I didn't get any "during" pictures, just some finished steps.  I put it together and threw some wood brown paint at it...and it stuck!

     while this was drying, i looked at the anchor boxes and cut out the parts for them.....and, of course...more sanding.  I knew i had some felt buttons around her somewhere......ahhh, here they are.  I put four buttons at each corner of the base and four on each of the posts.

      I couldn't help it.....I fell in love!   then I thought that i couldn't.......it might get damaged......so I made another.  I went to the hobby store, got the necessary wood and made it up.  I may put the felt buttons on it, but I haven't yet.  I want to make a plaque in the center and make a decal for it...."the Nordkap 476" is what it will say.

   and now, a sneak peak of what 'ole Nordie will look like in the next day or two.

     you can see from the shading......there's more sanding.